Tamil Nadu Police Sub-Inspector (SI) /Quantitative Aptitude

Percentages

Arithmetic · free study notes

Percentages – Advanced Study Notes

(For the Tamil Nadu Police Sub‑Inspector (SI) Examination – Quantitative Aptitude)


1. Introduction

Percentages are a unit‑free way of comparing two quantities that are proportional to a common quantity.

  • Definition:
    [ \text{Percent} = \frac{\text{Part}}{\text{Whole}}\times 100% ]
  • Historical remark: The word percent comes from Latin per centum (“by the hundred”), reflecting the fact that a percentage is a ratio to 100.

In the SI exam, percentages are used to:

  • Compare rates, growth, profit/loss, interest, tax, etc.
  • Solve problems involving change (increase/decrease), proportionality, and inverse relationships.

2. Fundamental Principles

Symbol Meaning Formula
(P) Whole (usually “100” in a percentage) (P = 100)
(p) Part (p = \frac{\text{Part}}{\text{Whole}}\times 100)
(x) Percentage rate (x% = \frac{x}{100})
(r) Ratio (r = \frac{a}{b})

2.1 Conversion between forms

Type Formula Example
Percentage ↔ Decimal (x% = \frac{x}{100}) (25% = 0.25)
Decimal ↔ Fraction (\frac{x}{100} = \frac{x}{100}) (0.75 = \frac{3}{4})
Fraction ↔ Percentage (\frac{a}{b}\times 100% = \frac{a}{b}\times 100% ) (\frac{1}{4} = 25%)

2.2 Scaling property

If a quantity (Q) is increased by (k%), the new quantity is: [ Q_{\text{new}} = Q \times \left(1 + \frac{k}{100}\right) ] If decreased by (k%): [ Q_{\text{new}} = Q \times \left(1 - \frac{k}{100}\right) ]


3. Advanced Topics

3.1 Compound Percentage Changes

When successive changes occur, the total change is multiplicative, not additive.

Given two successive changes (k_1%) and (k_2%): [ Q_{\text{final}} = Q \times \left(1 + \frac{k_1}{100}\right) \times \left(1 + \frac{k_2}{100}\right) ]

Example (Compound Interest)
Annual interest (r%) compounded (n) times a year on principal (P): [ A = P\left(1 + \frac{r}{100n}\right)^{nt} ]

3.2 Inverse Percentages

If a quantity (A) is (p%) of quantity (B), then (B) is (\frac{100}{p}%) of (A).

Edge case: When (p = 0) or (p = 100), the inverse is undefined or trivial.

3.3 Percent of a Percent – “Percent‑of‑Percent”

If a number (X) is (a%) of (Y), and (Y) itself is (b%) of (Z), then: [ X = Y \times \frac{a}{100} = Z \times \frac{b}{100} \times \frac{a}{100} ] Thus (X) is (\frac{ab}{10,000}%) of (Z).

3.4 Percent Change – Growth & Decline

If (A_1) changes to (A_2), percent change: [ \Delta% = \frac{A_2 - A_1}{A_1}\times 100% ]

Important: If (A_1) is zero, change is undefined (division by zero).

3.5 Percent Error & Accuracy

Useful in verifying computations: [ \text{Percent Error} = \frac{| \text{Measured} - \text{True} |}{|\text{True}|}\times 100% ]


4. Rigor & Proofs

4.1 Proof of the scaling property

Let (Q_{\text{new}} = Q + \Delta Q).
If the increase is (k%): [ \frac{\Delta Q}{Q} = \frac{k}{100};\Rightarrow;\Delta Q = Q\cdot \frac{k}{100} ] Hence, [ Q_{\text{new}} = Q + Q\cdot \frac{k}{100} = Q\left(1 + \frac{k}{100}\right) ]

4.2 Proof of multiplicative effect of successive changes

Let (Q_1 = Q\left(1 + \frac{k_1}{100}\right)).
Applying (k_2%) to (Q_1): [ Q_2 = Q_1 \left(1 + \frac{k_2}{100}\right) = Q\left(1 + \frac{k_1}{100}\right)\left(1 + \frac{k_2}{100}\right) ] Thus the total effect is the product of the individual factors.


5. Edge Cases & Common Pitfalls

Scenario What to watch out for Typical error
Percent of zero Division by zero “% of 0 = 0” is true only if numerator is 0
Negative percentages Decrease vs. increase Misinterpreting “-20%” as “20% decrease”
Percent change from 0 to non‑zero Undefined “Percentage increase from 0 to 5” is undefined
Compound vs. simple Additive vs. multiplicative Adding 10% and 20% gives 30% (wrong) – correct is 1.1×1.2=1.32 → 32%
Percent of a percent Mis‑placing the decimal 5% of

Your note

Page 1

Doubt hai is topic me?

Free AI teacher se poocho — 24/7, step by step.