Welder (ITI) – Fundamentals
Topic: Basic Principles
1. Simple Explanation
The basic principles of welding describe the how and why a weld is formed.
- Heat input: Energy supplied to melt the base metal and filler.
- Metallurgical bonding: Fusion of metal atoms across the joint.
- Cooling: Controlled solidification to control micro‑structure and residual stresses.
- Welding parameters: Voltage, current, travel speed, electrode angle, shielding gas, etc., all influence the weld pool shape, penetration, and quality.
In short: Heat melts → atoms mix → solidify → metal bonds.
2. Key Points
| # | Principle | What It Means | Typical Parameter/Control |
|---|---|---|---|
| 1 | Heat Source | Electrical arc, resistance, or gas (MIG, TIG, Stick, SMAW, etc.) | Voltage, current, gas flow |
| 2 | Fusion Zone | Area where metal is melted; determines weld shape | Travel speed, torch angle |
| 3 | Heat Affected Zone (HAZ) | Adjacent metal that hardens or softens due to temperature change | Pre‑heat, post‑heat, shielding gas |
| 4 | Metallurgical Bonding | Inter‑diffusion of atoms forming a new solid solution | Filler material, base metal compatibility |
| 5 | Cooling Rate | Fast cooling → hard micro‑structure; slow cooling → softer | Post‑heat, joint design |
| 6 | Residual Stresses | Develop from uneven cooling; cause distortion | Interpass cooling, stress relief |
| 7 | Weld Defects | Porosity, cracks, under‑penetration, etc. | Cleanliness, proper settings, technique |
| 8 | Safety | Arc flash, fumes, radiation, heat | PPE, ventilation, grounding |
3. Worked Example
Scenario
A welder needs to join two 1‑inch thick steel plates (AISI 1045) using MIG welding.
Given
- Voltage = 30 V
- Current = 200 A
- Travel speed = 40 in/min
- Shielding gas = 75% Ar / 25% CO₂
- Filler wire = ER70S‑6 (compatible with 1045)
Objectives
- Achieve full penetration.
- Minimize HAZ hardening.
- Avoid under‑penetration.
Calculations & Checks
| Step | Rationale | Expected Outcome |
|---|---|---|
| 1. Heat Input | ( Q = \frac{V \times I}{S} ) where (S) = travel speed (in/min) | ( Q = \frac{30 \times 200}{40} = 150 \text{ BTU/in}) – sufficient for 1‑inch penetration |
| 2. Filler Size | Use 1/8” (3.2 mm) wire for 1‑inch plates | Adequate bead on top, good fusion |
| 3. Gas Flow | 20–25 L/min (≈ 1 ft³/min) | Clean arc, stable weld pool |
| 4. Torch Angle | 10–15° from vertical, lead the travel | Proper shielding, reduced spatter |
| 5. Joint Preparation | Clean with solvent, bevel plates 30° each side | Good root coverage, reduced porosity |
| 6. Pre‑heat | 150 °F (≈80 °C) for 1045 steel | Reduces hardening, lowers residual stress |
| 7. Interpass Cooling | Allow 5–10 min between passes | Prevents excessive HAZ hardening |
| 8. Post‑heat | 200 °F for 30 min (or water‑bath) | Stress relief, fine micro‑structure |
Result
- Full penetration achieved.
- HAZ width ~0.3–0.4 in, acceptable hardness.
- Minimal distortion, clean bead.
4. Quick Revision Summary
| Topic | Take‑away |
|---|---|
| Heat Input | Voltage × Current ÷ Travel speed = BTU/in |
| Fusion | Proper settings → stable pool, full penetration |
| HAZ | Controlled cooling → avoid hardening |
| Residual Stress | Interpass cooling, post‑heat, joint design |
| Defects | Cleanliness, correct gas, proper torch angle |
| Safety | PPE, grounding, ventilation |
Tip: Before each weld, check the heat input, joint prep, and gas flow. Adjust one parameter at a time and observe the bead quality.